Paint & humidity

A lot has changed since our last post. We have managed to get our first coats of high build undercoat on, but not without a battle with the weather.

Turns out Tassy has humidity levels not dissimilar to the tropics, something we had not fully understood until now! Our magic figures for painting are: temperature no less than 10ºC and a maximum humidity of 80%. We have struggled to meet these critera, so have decided to keep moving forward with the decking, while we wait for conditions to improve.

We took a week off the build, to travel to Hobart to help Pete’s parents who’s house was flooded in the recent storm that caused massive damage in southern Tas. We also took the oppertunity to collect some additional plywood for completing the decks, superstructure and cockpit furniture..

IMG_0189

Deb finishing up the last of the sanding, prior to masking.

img_0190.jpg

Before we could paint, we needed to mask off the boundaries between the paint and varnish areas.

img_0368.jpg

After masking, we taped down protective sheeting on the floors and bench tops.

IMG_0366

The saloon floor, masked and tarped.

img_0365.jpg

We seem to have inherited a ships cat! This is smokey, a local resident who keeps us company from time to time.

IMG_0379

Spray day arrives. Temp and humidity OK … lets go!

IMG_0197

First coat on, and suddenly, our world has changed again. Frame five and master bedroom.

IMG_0196

Saloon & storage areas.

IMG_0208

Guest room

IMG_0199

Deb using the left overs to touch up in the galley.

IMG_0204

Bathroom.

To keep things ticking over while we wait for the weather to improve, we began preparing for decking. First we got the fore-beam ready for  permanent installation. This involved drilling four 16mm bolt holes for the big 5/8″ bolts specified in the plans. This thing is close to 2.4 meters from the ground, so after drilling, we lifted it down, so that we could continue work at ground level.

IMG_0209

 Drilling the bolt holes required the use of a long auger. We will also epoxy the beam in place, prior to laying the fore-deck over the top. 

An optional feature of the fore-beam is a fairing made from cutting an 150mm PVC pipe in half, and mounting on the forward face of the beam. It serves to soften the appearance of the square beam, plus provides some level of shock absorbtion in the event of a collision.

IMG_0216

After installing cleats on the beam, the next job was to cut the PVC pipe in half…

IMG_0219

 …then fix it in place with SS screws. Tomorrow deb will cover with two layers of glass. After that fixing points for the trampolines will be glassed in, then the whole lot coated with Qcell and sanded before fixing back in place on the boat.

 

6 thoughts on “Paint & humidity

  1. svtakeiteasy says:

    Bummer about the humidity and low temperatures… when we resprayed TIE the paint went all dull because of low temps and we had to sand and redo! So not worse forcing things!
    Does not it look amazing inside once all white and bright.

    Liked by 1 person

    • selahcat says:

      Thanks Chris & Wade. Yeah the timing is looking good for painting the outside. Should be in the warmer weather. We were hoping to have the inside done before then however, to avoid doing the whole thing at once! Once the deck is laid we have the option of heating the internal spaces: so that is part of our current thinking.

      Liked by 1 person

  2. Paul Imms says:

    Ah, reminds me of when I was spray painting Kurura after the smoke damage went right through all the cabins. Your equipment is so much better. What a difference a coat of paint makes, looking great !

    Liked by 1 person

    • selahcat says:

      Thanks old bean. Spraying may be faster to apply, but we took a full week to mask off. Would rather spray than roll all the nooks and crannies though. Quite happy to be back on the tools for a while now, however. Epoxy based paints are not for the faint hearted. Fussy and expensive!

      Like

  3. J Dean Beaver says:

    Finally………. the suspense was killin me!
    It’s funny how others lives entangle. I’ve been checking every day for an update and wow what a difference. I so enjoy what you share and it helps motivate me because I can see wher I’ll be in a few years. Thank you so much for sharing your life with us!

    Like

    • selahcat says:

      Hi Jim. Thanks for your comments. I guess it’s summer for you: good building weather. Yes, it’s been a while between posts. Finish sanding and detailing work didn’t present many photo opportunities. We have totally underestimated how long it takes, especially when battling weather conditions. We were hoping to split interior/exterior finishing to avoid months of nothing but painting but the conditions are against that plan: so we adapt!

      Like

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s