Hatches, deck fittings, metalwork and painting the interior.

I can’t believe its nearly a full month since we finished external paint. As I write this it’s hard to work out where the days have gone, but a lot of fiddly jobs have been tackled, as well as finishing up internal paintwork. I have learned that the days between big jobs can be swallowed up in a myriad of admin and preparation tasks. Little “catch-up” jobs that are postponed during the busy times, but need to be completed to advance to the next stage. My nickname for these times is “changing of the guard”. Usually, it involves sourcing materials and tools, making lots of calls or eBay purchases, dismantling jigs or templates (or building new ones) and other project management work. An example of the sort of job that can at first seem fairly straightforward, but actually turned out to be very time consuming (and expensive) was purchasing all the stainless nuts, bolts, and washers. Purchasing piecemeal the cost is prohibitive. Buying in bulk reduces the cost but involved digging out all the relevant hardware from storage and calculating quantities and sizes. It took us two days and $300 to make up the list and purchase fastenings for the hatches, inspection ports, hinges, and sail tracks. So far we haven’t started on the winches and standing blocks. Unexpected things trip you up. We could not source the large diameter penny washers for mounting deck hardware, so they are literally on a slow ship from China.

Anyway, I don’t want to sound like we are complaining. It was actually a rather nice season as, for the first time, we could complete some finish-up jobs, that were deemed “done and ready” for launch day.  Also, after the stress of finishing the external paint before the weather closed in,  we allowed ourselves to relax a little and do some fun jobs, before heading inside to begin the last dreaded paint job, the interior.

IMG_0809

There was no logical reason to install the captains chair just yet … I just wanted to.

IMG_0781

We are particularly pleased with how the lazarette hatch came together.

DSC_0712

Lazarette hatch closed, ready to repel boarders! … breaking waves from behind, if we mistime a nasty river bar entrance.

DSC_0710

Steering locker hatch: hope I’ve left enough room to fit the steering gubbings.

dsc_0714-1.jpg

Inspection ports and swim ladder installed on the aft steps. All good fun.

DSC_0702

The holding tank locker has enough room for a useful space above the tank. I think we’ll store the stern kedge anchor and mooring lines here for quick access, or maybe a wet locker for wetsuits and snorkeling gear.

Eventually, we had to bite the bullet and make our way inside to finish up painting the interior, a job we tried to do 12 months ago, but were unable to complete, due to weather conditions. This time around, however, we have a lid, so by blocking the openings, we were able to use heaters to make the conditions right for painting. I took the opportunity to make templates for the side windows (that will later be used to cut the polycarbonate sheets) and use them to block the windows. I also made the frames for the front opening windows.

DSC_0717

By blocking the openings we were able to heat the interior for painting.

While this was happening Deb sanded and vacuumed all the interior surfaces and re-did the masking protecting the varnished floors and benches where necessary. Then there were no more excuses. We donned our hated face masks, mixed up more epoxy 2 part paint and armed with rollers and brushes, dove below to begin the last big painting job.

At the time of writing we are still only part way through, but expect to be finished by the end of next week.

DSC_0705

Deb checking the finish. We are going for a matt finish in the main living areas …

DSC_0707

…but will gloss the bathroom with polyurethane 2 pack.

DSC_0708

The master bedroom is nearly completed.

img_0807.jpg

Deb figured out a good use of a narrow shelf in the fore-peak

DSC_0709

Turret ceiling and sides still need another two or three coats.

While installing the deck hatches we had a happy but unexpected change of plans. The photo below is the hatch for the large storage locker situated between the sleeping cabins. Originally I had planned to use a secondhand hatch, which proved unsuitable. Russell, our brother and landlord, was visiting when I broke the bad news to Deb. Large deck hatches cost around $600. Russ quickly offered to make a traditional timber hatch for us, saying he would like to contribute to the build (as if he hadn’t already). Selah is being built using contemporary methods, all surfaces sealed with fiberglass, epoxy and/or two-part paints, with very little bright-work (varnished timber). The more we thought about it, a beautifully varnished hatch was a perfect way to pay homage to her Tasmanian origins, so we gratefully accepted Russ’ offer.

DSC_0723

The change of plan meant we had to build a hatch combing. Russell supplied some 10mm Oregon machined from the stock he sourced from a local boatbuilder.

DSC_0726

The hatch. We are thrilled by the result. Made from Tasmanian Oregon. Four coats of varnish on, another two to go. We will probably have to touch up every six months or so, a maintenance chore we are happy to accept.

Another ongoing job has been sourcing our metalwork. There have been challenges. Peter Snell, the designer provides drawn plans, but it seems local metalworking shops have largely transitioned to CAD/laser cut processes, and are not interested in hand cutting small jobs. I decided I needed to buy a CAD program and teach myself how to use it so I could provide digital files for all the components.  The chainplates and emergency tiller bracket were fairly straight forward, but the anchor retrieval componentry was more involved. I based my plans on an existing design by two Easy builders, James Coomer (Pure Majek)  and Chris Guthry (Outback Dreamer), but with a few modifications for our situation.  James has published them in his book,  A Catamaran Building Adventure.

Once I have checked (and triple checked) the dimensions, I’ll send them off for laser cutting, then deliver the components to a local welding shop.

Window_and_SARCA_setup_dxf_-_QCAD.jpg

The fabrication combines the forebeam A frame and anchor retrieval. Its mounted on the forebeam and catwalk.

 

5 thoughts on “Hatches, deck fittings, metalwork and painting the interior.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s